Continental Device India Limited. Data Sheet. Page 1 of 2. Continental Device India Limited. An ISO/TS , ISO and ISO Certified Company. CT Datasheet, CT PDF, CT Data sheet, CT manual, CT pdf, CT, datenblatt, Electronics CT, alldatasheet, free, datasheet. MCCT datasheet, MCCT pdf, MCCT data sheet, datasheet, data sheet, pdf, Fairchild Semiconductor, 3-Terminal 1A Positive Voltage Regulator.
|Published (Last):||24 December 2014|
|PDF File Size:||6.18 Mb|
|ePub File Size:||14.12 Mb|
|Price:||Free* [*Free Regsitration Required]|
In this article, we go over how to connect a voltage regulator to a circuit to get a specific DC output regulated voltage. Depending on the voltage regulator in use, we can get a regulated positive or negative voltage, at whichever voltage we want. The LM78XX voltage regulators are a popular kind for regulating and outputting positive voltage, while the LM79XX are a popular series of regulators for negative voltage.
In this article, we use a positive voltage regulator, which outputs 5V, the LM regulator. Before we can hook up the circuit, let’s first go over the pinout diagram of the voltage regulator, which is vital for hooking up the circuit.
A voltage regulator is a 3-terminal device. Pin 1 is the Input Pin. The output voltage of whatever voltage source you want to regulate down whether it’s a transformer, battery, etc.
So for instance, if you have 10 volts coming from a transformer that you want regulated down to 5 volts, the output of the transformer the 10 volts is fed into the regulator input pin 1 so that the regulator can regulate it down to your wanted voltage 5 volts. The voltage regulator should always be fed as smooth of a DC signal as possible which gives the best regulated output so it can regulate it down to its specified voltage. Remember, the input voltage has to be larger than the 7809c that the regulator regulates out.
In this case, we are using a LM, which outputs 5 volts. In order for the regulator to output 5 volts, the 7809cg entering has to be at least 2 volts higher, so it has to be at least 7 volts. However, for experimental purposes and ease of getting parts, we will use a 9-volt battery as our input voltage. Pin 2 is Ground. It hooks up to the ground in our circuit. Without ground, the circuit couldn’t be complete because the voltage wouldn’t have electric potential and the circuit wouldn’t have a return path.
Pin 3 is the Output Pin. This is the pin that gives out the regulated voltage, which, in this case, is 5 volts. At the end of this experiment, when our circuit is hooked up, we’re going to read out the voltage with a multimeter and it should give out close to 5 volts.
How to Connect a Voltage Regulator in a Circuit
Okay, now let’s build the circuit. If you don’t have all the parts, don’t feel bad. You can buy them at anytime and come back to this page and do the experiment anytime. For now, you can just follow along. Let’s view the complete circuit now and explanations will ensue.
The first capacitor, the 0. This capacitor is there to filter out any noise coming from the voltage source the battery.
The voltage regulator works best and will be most efficient when a clean DC signal is fed into it. We don’t want any ac noise ripple imposed on the DC line voltage. The capacitor, in essence, acts as a bypass capacitor. It shorts the AC signal of the voltage signal which is noise on the voltage signal to ground and only the DC portion of the signal goes into the regulator.
How to Connect a Voltage Regulator in a Circuit
The second capacitor, the 0. This capacitor is there again to filter out any noise or high-frequency ac signals that may be on the DC voltage line. For a circuit like this, where we’re lighting an LED, it isn’t exactly crucial to have a pure DC signal, but in other applications, such as when outputting voltage to power a logic chip, which needs a precise voltage fed into it in order to give the correct logic output, it is crucial.
That’s why it’s a good idea to get into hooking up a voltage regulator properly from the sart. Okay, so let’s recap on the circuit. The circuit begins at the 9-volt battery. This produces a voltage of 9 volts. The first capacitor, the ceramic 0. It shorts this noise to ground and allows the pure DC signal into the regulator. The regulator regulates this voltage down to 5 volts.
After it comes out of the regulator, the other capacitor, the 0.
Now this DC voltage, clean and crisp, is ready to power whatever you want it to, in this case, the load 7890ct a resistor and a LED. Keep in mind that the design datsheet a voltage regulator depends on the voltage regulator being used and the intended use of a circuit. Always consult the Manufacturer’s Datasheet for the voltage regulator in use for a circuit to see how to hook it up with the necessary required external components. Usually the only external components necessary are just capacitors, though heat sinks may also need to be added when heat dissipation is necessary.
The Datasheet specifies which value of capacitors to use, so datasjeet a good idea to learn from the people who manufacturered the chip. Also, design changes when dealing with the intended use of the circuit. When the load of a circuit is stable and unchanging, as in the example above, datasheett is usually not necessary to add a large electrolytic capacitor on the output to dstasheet as a smoothing capacitor. But if you’re going to have a varying load, a potentiometer, 780ct instance, on the output, it is well advised to add an electrolytic capacitor in parallel to the ceramic capacitor.
This dwtasheet capacitor acts as a smoothing capacitor, when load resistance changes cause abrupt voltage spikes and drops, in a circuit. This capacitor charges up with voltage when the circuit has excess spikes in current and discharges to supply voltage when the circuit is low on current. Therefore, it has a smoothing effect and even things out.
Essentially, it acts as a load balancer. More will be on this for more advanced projects, but this page is a good start for those starting off in connecting voltage regulators for basic circuits. Sign up for Our Newsletter Name: How to Connect a Voltage Regulator in a Circuit In this article, we go over how to connect a voltage regulator to a circuit to get a specific DC output regulated voltage.