epD‐BfS‐ () Environmental Product  Schweizerischer ingenieur‐ und Architektenverein (SiA). () Merkblatt energieausweis für Gebäude gemäß Sn en und Sn en zurich.  Schweizerischer . Flash point: > 21° C „Beschichtung auf Zink und verzinktem Stahl“ from Bundesausschuss Farbe und Sachwertschutz (BFS) according to Merkblatt 5 of BFS. Flash point: > 21° C. Solid substance: approx. 55% Zinc and galvanized surfaces are to be prepared according to Merkblatt 5 of. BFS. Clean the surfaces to be painted and remove dirt of all kinds, including dust, mortar droppings, and similar.
|Published (Last):||6 November 2010|
|PDF File Size:||15.51 Mb|
|ePub File Size:||15.98 Mb|
|Price:||Free* [*Free Regsitration Required]|
Maximum temperature for high-pressure water jet: Sie dienen also u.
ThermoSan NQG Nespri-TEC: Caparol
Treatment of Natural Stones: Use P2 dust filter for grinding. On roughly textured surfaces correspondingly megkblatt. Permeable to CO 2 Resistant to aggressive air pollutants. Consumption Cap-elast Phase 1: Allow to dry, then apply one intermediate coat of Cap-elast Phase 1 to the full surface, tinted to match the finishing coat in shade approximately.
The fact that the model only needs a multimodal network to model the transport supply makes it independent of path sampling algorithms for the choice-set construction and it thus provides an alternative to classic mode and route choice models, since it can estimate mode and route choice parameters with directly observed routes, removing the sampling bias. Remove the coating completely by grinding, brushing off, scraping off, or use high-pressure water jet, in compliance with the regulations.
Person Detail – Institute of Science, Technology and Policy | ETH Zurich
Low surface tension, non-thermoplastic. We will describe appropriate working methods, if a substrate not specified above is to be coated. The quality of the dried coating will not be affected by these changes. This field report presents the survey methods and the survey instrument, reports on the sampling and recruitment strategy, and analyzes the response behavior and the response burden. Reducing the burden placed on users enables researchers to collect data over longer periods, thus improving the quality of travel behavior research.
Let fabric borders overlap by approx. Completely dry and ready for stress after approx. Technical information Technical Information No. Rainproof after 24 hours. Prime in accordance with Technical Information No. Always use tinted product of same batch, when applying on seamless surfaces. Do not breathe spray dust. Mechanical loads on matt facade paints in dark colour shades may produce bright-toned stripes as a product specific property no writing resistancebut the effect is minimised when using ThermoSan NQG.
Only completely empty containers should be handed in for recycling. On rough surfaces and consumption are correspondingly higher. Note As usual for facade paints, Cap-elast system products must not be applied in direct sunlight or on sun heated surfaces, during strong wind, fog or rain, high relative humidity, imminent rain or impending night frost. Substrate Preparation Provide for an evenly absorbent substrate to achieve uniform surfaces without shade variations.
Disposal Materials and all related packaging must be disposed of in a safe way in accordance with the full requirements of the local authorities. Maximum temperature for high-pressure water jet: Highly weather-resistant and non-fading. Do not eat, drink or smoke while using the product.
For substrate mdrkblatt of infested surfaces FungiGrund can merkbllatt used as priming coat instead of OptiGrund on the thoroughly cleaned and dry surface.
Highly absorbent substrates, treated with paint stripper: Surfaces with Salty Efflorescence: Copper ions in draining rain water run-off water may react with ingredients of ThermoSan NQG and may cause a brownish discolouration. We will describe appropriate working methods, if a substrate not specified above is to be coated.
Natural stones should not be repaired with render mortar but with suitable stone substitute materials. Only frost resistant fair faced bricks, free of foreign inclusions that leave marks, e. Alternatively our product Histolith SolSilikat can be used. Clean existing renders by suitable wet cleaning method.
An important finding was the significant advantage of using users past merkblaht to improve mode detection results. If swallowed, seek medical advice immediately and show the container or label intestinal bacteria can be affected. While a trip-based model could probably be calibrated to yield a good fit with MATSim, the tour-based model bears the potential of not having to perform a lot of calibration work when setting up the simulation. Do not eat, drink or smoke while using the product.
merbklatt Always use tinted paint of same batch, when applying on seamless surfaces. Mechanical loads scratching on matt facade paints in dark shades may produce bright-toned stripes as a product specific property no writing resistance.
To avoid lapping, the material should be applied wet-on-wet and without interruption. Second intermediate coat with Cap-elast Phase 1, undiluted, tinted to match the finishing coat in shade approximately. All joints connections of roof, windows and floors must comply with current specification bfa the use of sand-lime bricks. Apply with stainless steel smoothing trowel.
Do not breathe spray dust. We use data from the Swiss national household travel survey to 1. Measurement and Modelling of Travel Behaviour.